ICS Diamond Tools

680ES PG Gas Power Cutter for Pipe Cutting
Now with PowerGrit® and 50:1 (2%) Fuel-to-oil!

Description

Built to provide a combination of performance and portability for cutting in-ground utility pipe, the 680ES-PG Gas Power Cutter with PowerGrit® chain will change the way you cut pipe.

The 680ES PG allows you to cut up to 10 in. deep into ductile iron, cast iron, PVC, HDPE, and Insituform lining, and is also designed to fit the full line of FORCE3® Series chains.

With a quick switch of the guide bar, chain, and drive sprocket, you can use this power cutter in masonry, stone, and even reinforced concrete.

The 680ES-PG may be the most cost-effective, versatile tool in your arsenal.

WARNING:
This product can expose you to chemicals, including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

680ES Powerhead only MSRP $1469
680ES Saw packages start at MSRP $2144
Click below to purchase or to see other packages.

FEATURES AND BENEFITS

  • Polyester air filter designed specifically for wet cutting
  • Operates PowerGrit Pipe Cutting saw chain
  • Multifunction lever controls choke, throttle advance, run and stop modes
  • Extended drive sprocket adapter offers easy chain assembly
  • Deep cutting solution for obstructed or small openings
  • Easy-to-start in all weather

Engine Type 2-stroke, Air Cooled
Displacement 76.5 cc (4.7 cu-in)
Horsepower 3.7 kW (5 hp) @ 9,500 rpm
Torque 4.1 Nm (36.3 in-lbs) @ 6,500 rpm
Engine Speed 11500 +/- 500 rpm (max) / 2,800 - 3,200 rpm (Idle)
Chain Speed at Maximum Power 34.5 m/s (6800 ft /min)
Weight 9.5 kg (21 lbs) powerhead only
Dimensions 46 cm (18 in) length / 29 cm (11.5 in) height / 25 cm (10 in) width
Starter Dust and water resistant
Ignition Special water resistant electronic ignition
Fuel ratio 4% (25:1) gasoline-to-oil
Fuel Capacity 0.88 liter (0.23 gallon)
Water Supply Requirement Minimum: 1.5 bar (20 psi)
Water Flow Requirement Minimum: 4 lpm (1 gpm)
Guaranteed Sound Power Level, Lwa (1) 117 dB(A) (Kwa=3.0 dB(A))
Equivalent Sound Pressure at the Operator's Ear Lwa 101.0 dB(A) (K = 2.0 dB(A))
Vibration, ahv eq Concrete Cutting (2) 7.2 m/s2 (K=1.0 m/s2) Front Handle/8.5 m/s2 (K=1.0 m/s2) Rear Handle

1) Measured in accordance with ANSI S12.51-2012/ISO3741:2010 / (2) Measured in accordance with ISO5349=1:2001 and IS 22867:2011

Product Support

Get help with troubleshooting and service issues.

Find Support

Product Registration

Activate your warranty and get premium support and more.

Register a Product

Featured Videos

695 Air Filter and Spark Plug

Replacing these two inexpensive items regularly can extend the life of your saw. Click below for instructions

695 and 890 Post Use Recommendations

You’re done for the day, we show you how put your tools away clean and ready for tomorrow

695 Daily Inspection

How to inspect the 695 daily to get the best life out of your saw

Also Available

2-Stroke Engine Oil

View Product

3P8 HF Wire Saw

View Product

680ES Gas Power Cutter

View Product